Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-156652

Aircraft Structure, Surfaces, Rigging, and Systems Assemblers

Palm Bay-Melbourne-Titusville, FLGovernment job code 51-2011

Market pay · all workers · BLS, May 2025

$59,080median pay per year · $28.41 an hour
10th
$47,450
25th
$49,660
Median
$59,080
75th
$75,250
90th
$80,620

Government wage levels · wage year 2026-27

Level I
$47,403
Level II
$54,725
Level III
$62,026
Level IV
$69,347

The four pay levels the Department of Labor sets for this job in Palm Bay-Melbourne-Titusville, FL. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
310
Against the U.S. median
−10%
Mean pay per year
$62,100
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-156652

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash 2c97ee4c · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-156652

What Does This Job Pay in Palm Bay-Melbourne-Titusville, FL?

Aircraft Structure, Surfaces, Rigging, and Systems Assemblers in Palm Bay-Melbourne-Titusville, FL earn a median of $59,080 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $49,660 and $75,250. The lowest-paid tenth earn under $47,450 and the highest-paid tenth earn over $80,620. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 10% below the national median of $65,380 for the same job.
  • It is 9% below the Florida median of $64,580.
  • 310 people hold this job here, 0.9% of the 34,020 who hold it across the country.
  • Of every 1,000 jobs here, 1.25 are this job, which makes it 5.7 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $49,660 and $75,250, a band $25,590 wide.
  • Pay at the 90th percentile ($80,620) is 1.7 times pay at the 10th ($47,450).
  • The average (mean) is $62,100, 5% above the median. An average above the median means a smaller group of high earners pulls it up.
  • By the hour, the published median is $28.41.
  • The market median of $59,080 meets government wage Level II for this job and area (wage year 2026-27).

What Aircraft Structure, Surfaces, Rigging, and Systems Assemblers Do

Assemble, fit, fasten, and install parts of airplanes, space vehicles, or missiles, such as tails, wings, fuselage, bulkheads, stabilizers, landing gear, rigging and control equipment, or heating and ventilating systems.

Common job titles: Aircraft Assembler, Aircraft Line Assembler, Assembler, Assembly Riveter, Assembly Technician (Assembly Tech), Sheet Metal Assembler and Riveter (SMAR), Sheet Metal Mechanic, Sheet Metal Technician (Sheet Metal Tech), Structures Mechanic, Structures Technician (Structures Tech).

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Read blueprints, illustrations, or specifications to determine layouts, sequences of operations, or identities or relationships of parts.
  • Inspect or test installed units, parts, systems, or assemblies for fit, alignment, performance, defects, or compliance with standards, using measuring instruments or test equipment.
  • Set, align, adjust, or synchronize aircraft armament or rigging or control system components to established tolerances or requirements, using sighting devices and hand tools.
  • Join structural assemblies, such as wings, tails, or fuselage.
  • Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.

Education. 55% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.