Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-156660

Aircraft Structure, Surfaces, Rigging, and Systems Assemblers

Tucson, AZGovernment job code 51-2011

Market pay · all workers · BLS, May 2025

$73,930median pay per year · $35.54 an hour
10th
$58,690
25th
$58,690
Median
$73,930
75th
$73,930
90th
$90,850

Government wage levels · wage year 2026-27

Level I
$55,619
Level II
$63,086
Level III
$70,574
Level IV
$78,042

The four pay levels the Department of Labor sets for this job in Tucson, AZ. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
580
Against the U.S. median
+13%
Mean pay per year
$70,640
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-156660

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash 6bd05bb8 · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-156660

What Does This Job Pay in Tucson, AZ?

Aircraft Structure, Surfaces, Rigging, and Systems Assemblers in Tucson, AZ earn a median of $73,930 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $58,690 and $73,930. The lowest-paid tenth earn under $58,690 and the highest-paid tenth earn over $90,850. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 13% above the national median of $65,380 for the same job.
  • It is about the same as the Arizona median of $73,930.
  • 580 people hold this job here, 1.7% of the 34,020 who hold it across the country.
  • Of every 1,000 jobs here, 1.49 are this job, which makes it 6.8 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $58,690 and $73,930, a band $15,240 wide.
  • Pay at the 90th percentile ($90,850) is 1.5 times pay at the 10th ($58,690).
  • The average (mean) is $70,640, 4% below the median, so more of the spread lies on the low side.
  • By the hour, the published median is $35.54.
  • The market median of $73,930 meets government wage Level III for this job and area (wage year 2026-27).

What Aircraft Structure, Surfaces, Rigging, and Systems Assemblers Do

Assemble, fit, fasten, and install parts of airplanes, space vehicles, or missiles, such as tails, wings, fuselage, bulkheads, stabilizers, landing gear, rigging and control equipment, or heating and ventilating systems.

Common job titles: Aircraft Assembler, Aircraft Line Assembler, Assembler, Assembly Riveter, Assembly Technician (Assembly Tech), Sheet Metal Assembler and Riveter (SMAR), Sheet Metal Mechanic, Sheet Metal Technician (Sheet Metal Tech), Structures Mechanic, Structures Technician (Structures Tech).

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Read blueprints, illustrations, or specifications to determine layouts, sequences of operations, or identities or relationships of parts.
  • Inspect or test installed units, parts, systems, or assemblies for fit, alignment, performance, defects, or compliance with standards, using measuring instruments or test equipment.
  • Set, align, adjust, or synchronize aircraft armament or rigging or control system components to established tolerances or requirements, using sighting devices and hand tools.
  • Join structural assemblies, such as wings, tails, or fuselage.
  • Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.

Education. 55% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.