Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-63268

Calibration Technologists and Technicians

Fort Wayne, INGovernment job code 17-3028

Market pay · all workers · BLS, May 2025

$51,310median pay per year · $24.67 an hour
10th
$35,790
25th
$46,920
Median
$51,310
75th
$65,830
90th
$72,790

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$42,370
Level II
$49,816
Level III
$57,242
Level IV
$64,688

The four pay levels the Department of Labor sets for this job in Fort Wayne, IN. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
60
Against the U.S. median
−24%
Mean pay per year
$57,330
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-63268

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash dcf4e4bf · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-63268

What Does This Job Pay in Fort Wayne, IN?

Calibration Technologists and Technicians in Fort Wayne, IN earn a median of $51,310 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $46,920 and $65,830. The lowest-paid tenth earn under $35,790 and the highest-paid tenth earn over $72,790. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 24% below the national median of $67,820 for the same job.
  • It is 17% below the Indiana median of $61,930.
  • 60 people hold this job here, 0.4% of the 16,540 who hold it across the country.
  • Of every 1,000 jobs here, 0.28 are this job, which makes it 2.7 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $46,920 and $65,830, a band $18,910 wide.
  • Pay at the 90th percentile ($72,790) is 2.0 times pay at the 10th ($35,790).
  • The average (mean) is $57,330, 12% above the median. An average above the median means a smaller group of high earners pulls it up.
  • By the hour, the published median is $24.67.
  • The market median of $51,310 meets government wage Level II for this job and area (wage year 2026-27).

What Calibration Technologists and Technicians Do

Execute or adapt procedures and techniques for calibrating measurement devices, by applying knowledge of measurement science, mathematics, physics, chemistry, and electronics, sometimes under the direction of engineering staff. Determine measurement standard suitability for calibrating measurement devices. May perform preventive maintenance on equipment. May perform corrective actions to address identified calibration problems.

Common job titles: Calibration Specialist, Calibration Technician (Calibration Tech), Gauge Specialist, Instrument and Control Technician (I and C Tech), Instrument Control Technician (Instrument Control Tech), Quality Technician (Quality Tech).

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Maintain or repair measurement devices or equipment used for calibration testing.
  • Conduct calibration tests to determine performance or reliability of mechanical, structural, or electromechanical equipment.
  • Verify part dimensions or clearances using precision measuring instruments to ensure conformance to specifications.
  • Read blueprints, schematics, diagrams, or technical orders.
  • Visually inspect equipment to detect surface defects.

Preparation This Job Usually Needs

Job Zone Three: Medium Preparation Needed. Most occupations in this zone require training in vocational schools, related on-the-job experience, or an associate's degree. Employees in these occupations usually need one or two years of training involving both on-the-job experience and informal training with experienced workers. A recognized apprenticeship program may be associated with these occupations. Previous work-related skill, knowledge, or experience is required for these occupations. For example, an electrician must have completed three or four years of apprenticeship or several years of vocational training, and often must have passed a licensing exam, in order to perform the job.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.