Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-156700

Coil Winders, Tapers, and Finishers

Waterbury-Shelton, CTGovernment job code 51-2021

Market pay · all workers · BLS, May 2025

$37,290median pay per year · $17.93 an hour
10th
$36,920
25th
$37,020
Median
$37,290
75th
$43,410
90th
$45,610

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$36,920
Level II
$38,584
Level III
$40,227
Level IV
$41,891

The four pay levels the Department of Labor sets for this job in Waterbury-Shelton, CT. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
80
Against the U.S. median
−23%
Mean pay per year
$40,250
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-156700

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash 18d24a51 · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-156700

What Does This Job Pay in Waterbury-Shelton, CT?

Coil Winders, Tapers, and Finishers in Waterbury-Shelton, CT earn a median of $37,290 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $37,020 and $43,410. The lowest-paid tenth earn under $36,920 and the highest-paid tenth earn over $45,610. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 23% below the national median of $48,220 for the same job.
  • It is 12% below the Connecticut median of $42,220.
  • 80 people hold this job here, 0.6% of the 12,840 who hold it across the country.
  • Of every 1,000 jobs here, 0.52 are this job, which makes it 6.3 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $37,020 and $43,410, a band $6,390 wide.
  • Pay at the 90th percentile ($45,610) is 1.2 times pay at the 10th ($36,920).
  • The average (mean) is $40,250, 8% above the median. An average above the median means a smaller group of high earners pulls it up.
  • By the hour, the published median is $17.93.
  • The market median of $37,290 meets government wage Level I for this job and area (wage year 2026-27).

Connecticut requires pay or a pay range in job ads from covered employers. What Connecticut’s rule says

What Coil Winders, Tapers, and Finishers Do

Wind wire coils used in electrical components, such as resistors and transformers, and in electrical equipment and instruments, such as field cores, bobbins, armature cores, electrical motors, generators, and control equipment.

Common job titles: Armature Winder, Auto-Winder, Coil Finisher, Coil Winder, Hand Winder, Motor Winder, Winder, Winder Operator.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Operate or tend wire-coiling machines to wind wire coils used in electrical components such as resistors and transformers, and in electrical equipment and instruments such as bobbins and generators.
  • Attach, alter, and trim materials such as wire, insulation, and coils, using hand tools.
  • Review work orders and specifications to determine materials needed and types of parts to be processed.
  • Cut, strip, and bend wire leads at ends of coils, using pliers and wire scrapers.
  • Examine and test wired electrical components such as motors, armatures, and stators, using measuring devices, and record test results.

Education. 57% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.