Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-165580

Cutting and Slicing Machine Setters, Operators, and Tenders

Gulfport-Biloxi, MSGovernment job code 51-9032

Market pay · all workers · BLS, May 2025

$39,580median pay per year · $19.03 an hour
10th
$29,880
25th
$29,880
Median
$39,580
75th
$46,000
90th
$48,480

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$28,912
Level II
$33,363
Level III
$37,814
Level IV
$42,266

The four pay levels the Department of Labor sets for this job in Gulfport-Biloxi, MS. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
40
Against the U.S. median
−15%
Mean pay per year
$37,860
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-165580

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash 4723362a · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-165580

What Does This Job Pay in Gulfport-Biloxi, MS?

Cutting and Slicing Machine Setters, Operators, and Tenders in Gulfport-Biloxi, MS earn a median of $39,580 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $29,880 and $46,000. The lowest-paid tenth earn under $29,880 and the highest-paid tenth earn over $48,480. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 15% below the national median of $46,570 for the same job.
  • It is 5% below the Mississippi median of $41,590.
  • 40 people hold this job here, less than 0.1% of the 44,980 who hold it across the country.
  • Of every 1,000 jobs here, 0.23 are this job, which makes it 19% less common here than in the U.S. as a whole.
  • The middle half of workers earn between $29,880 and $46,000, a band $16,120 wide.
  • Pay at the 90th percentile ($48,480) is 1.6 times pay at the 10th ($29,880).
  • The average (mean) is $37,860, 4% below the median, so more of the spread lies on the low side.
  • By the hour, the published median is $19.03.
  • The market median of $39,580 meets government wage Level III for this job and area (wage year 2026-27).

What Cutting and Slicing Machine Setters, Operators, and Tenders Do

Set up, operate, or tend machines that cut or slice materials, such as glass, stone, cork, rubber, tobacco, food, paper, or insulating material.

Common job titles: Cutter, Cutter Operator, Cutting Machine Operator, Die Cutter Operator, Flat Cutter, Machine Operator, Paper Cutter, Sheeter, Skiver Operator, Slitter.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Remove defective or substandard materials from machines, and readjust machine components so that products meet standards.
  • Maintain production records, such as quantities, types, and dimensions of materials produced.
  • Start machines to verify setups, and make any necessary adjustments.
  • Press buttons, pull levers, or depress pedals to start and operate cutting and slicing machines.
  • Start pumps to circulate water and abrasives onto blades or cables during cutting.

Education. 92% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.