Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-149218

Electric Motor, Power Tool, and Related Repairers

Greensboro-High Point, NCGovernment job code 49-2092

Market pay · all workers · BLS, May 2025

$45,310median pay per year · $21.78 an hour
10th
$34,340
25th
$35,350
Median
$45,310
75th
$47,030
90th
$56,440

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$34,445
Level II
$39,270
Level III
$44,096
Level IV
$48,922

The four pay levels the Department of Labor sets for this job in Greensboro-High Point, NC. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
40
Against the U.S. median
−19%
Mean pay per year
$44,140
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-149218

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash ff95442f · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-149218

What Does This Job Pay in Greensboro-High Point, NC?

Electric Motor, Power Tool, and Related Repairers in Greensboro-High Point, NC earn a median of $45,310 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $35,350 and $47,030. The lowest-paid tenth earn under $34,340 and the highest-paid tenth earn over $56,440. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 19% below the national median of $56,210 for the same job.
  • It is 2% below the North Carolina median of $46,320.
  • 40 people hold this job here, 0.3% of the 14,450 who hold it across the country.
  • Of every 1,000 jobs here, 0.12 are this job, which makes it 30% more common here than in the U.S. as a whole.
  • The middle half of workers earn between $35,350 and $47,030, a band $11,680 wide.
  • Pay at the 90th percentile ($56,440) is 1.6 times pay at the 10th ($34,340).
  • The average (mean) is $44,140, 3% below the median, so more of the spread lies on the low side.
  • By the hour, the published median is $21.78.
  • The market median of $45,310 meets government wage Level III for this job and area (wage year 2026-27).

What Electric Motor, Power Tool, and Related Repairers Do

Repair, maintain, or install electric motors, wiring, or switches.

Common job titles: Electric Motor Mechanic, Electric Motor Repairman, Electric Motor Winder, Electro Mechanic, Maintenance Technician, Power Tool Repair Technician, Repair Technician, Service Technician, Tool Repair Technician, Tool Technician.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
  • Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
  • Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
  • Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
  • Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.

Education. 39% of workers surveyed by O*NET said the level required for this job is: Post-Secondary Certificate.

Preparation This Job Usually Needs

Job Zone Three: Medium Preparation Needed. Most occupations in this zone require training in vocational schools, related on-the-job experience, or an associate's degree. Employees in these occupations usually need one or two years of training involving both on-the-job experience and informal training with experienced workers. A recognized apprenticeship program may be associated with these occupations. Previous work-related skill, knowledge, or experience is required for these occupations. For example, an electrician must have completed three or four years of apprenticeship or several years of vocational training, and often must have passed a licensing exam, in order to perform the job.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.