Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-31105

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic

DelawareGovernment job code 51-4021

Market pay · all workers · BLS, May 2025

$46,140median pay per year · $22.18 an hour
10th
$36,930
25th
$45,640
Median
$46,140
75th
$57,810
90th
$59,480

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels

Wage levels are set for each local area. Open a metro card for this job to see them.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
470
Against the U.S. median
−3%
Mean pay per year
$49,830
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-31105

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash b169a99b · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-31105

What Does This Job Pay in Delaware?

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic in Delaware earn a median of $46,140 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $45,640 and $57,810. The lowest-paid tenth earn under $36,930 and the highest-paid tenth earn over $59,480. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 3% below the national median of $47,720 for the same job.
  • 470 people hold this job here, 0.8% of the 60,840 who hold it across the country.
  • Of every 1,000 jobs here, 0.97 are this job, which makes it 2.5 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $45,640 and $57,810, a band $12,170 wide.
  • Pay at the 90th percentile ($59,480) is 1.6 times pay at the 10th ($36,930).
  • The average (mean) is $49,830, 8% above the median. An average above the median means a smaller group of high earners pulls it up.
  • By the hour, the published median is $22.18.

Delaware has enacted a law that will require pay in job ads from Sep 26, 2027. What Delaware’s rule says

What Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic Do

Set up, operate, or tend machines to extrude or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes.

Common job titles: Equipment Technician (Equipment Tech), Extruder Operator, Extrusion Line Operator, Extrusion Operator, Extrusion Press Operator, Machine Operator, Metal Inspector, Setup Operator, Wire Mill Operator, Wire Mill Rover.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Reel extruded products into rolls of specified lengths and weights.
  • Measure and examine extruded products to locate defects and to check for conformance to specifications, adjusting controls as necessary to alter products.
  • Start machines and set controls to regulate vacuum, air pressure, sizing rings, and temperature, and to synchronize speed of extrusion.
  • Weigh and mix pelletized, granular, or powdered thermoplastic materials and coloring pigments.
  • Determine setup procedures and select machine dies and parts, according to specifications.

Education. 61% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.