Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-159084

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic

Greensboro-High Point, NCGovernment job code 51-4021

Market pay · all workers · BLS, May 2025

$60,390median pay per year · $29.03 an hour
10th
$45,000
25th
$49,060
Median
$60,390
75th
$60,390
90th
$60,390

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$45,656
Level II
$50,440
Level III
$55,245
Level IV
$60,029

The four pay levels the Department of Labor sets for this job in Greensboro-High Point, NC. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
430
Against the U.S. median
+27%
Mean pay per year
$55,280
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-159084

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash a1522af3 · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-159084

What Does This Job Pay in Greensboro-High Point, NC?

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic in Greensboro-High Point, NC earn a median of $60,390 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $49,060 and $60,390. The lowest-paid tenth earn under $45,000 and the highest-paid tenth earn over $60,390. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 27% above the national median of $47,720 for the same job.
  • It is 13% above the North Carolina median of $53,330.
  • 430 people hold this job here, 0.7% of the 60,840 who hold it across the country.
  • Of every 1,000 jobs here, 1.17 are this job, which makes it 3.0 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $49,060 and $60,390, a band $11,330 wide.
  • Pay at the 90th percentile ($60,390) is 1.3 times pay at the 10th ($45,000).
  • The average (mean) is $55,280, 8% below the median, so more of the spread lies on the low side.
  • By the hour, the published median is $29.03.
  • The market median of $60,390 meets government wage Level IV for this job and area (wage year 2026-27).

What Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic Do

Set up, operate, or tend machines to extrude or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes.

Common job titles: Equipment Technician (Equipment Tech), Extruder Operator, Extrusion Line Operator, Extrusion Operator, Extrusion Press Operator, Machine Operator, Metal Inspector, Setup Operator, Wire Mill Operator, Wire Mill Rover.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Reel extruded products into rolls of specified lengths and weights.
  • Measure and examine extruded products to locate defects and to check for conformance to specifications, adjusting controls as necessary to alter products.
  • Start machines and set controls to regulate vacuum, air pressure, sizing rings, and temperature, and to synchronize speed of extrusion.
  • Weigh and mix pelletized, granular, or powdered thermoplastic materials and coloring pigments.
  • Determine setup procedures and select machine dies and parts, according to specifications.

Education. 61% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.