Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-31110

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic

IllinoisGovernment job code 51-4021

Market pay · all workers · BLS, May 2025

$48,520median pay per year · $23.33 an hour
10th
$33,800
25th
$39,400
Median
$48,520
75th
$58,310
90th
$70,470

Government wage levels

Wage levels are set for each local area. Open a metro card for this job to see them.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
2,750
Against the U.S. median
+2%
Mean pay per year
$50,450
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-31110

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash 0fbffa16 · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-31110

What Does This Job Pay in Illinois?

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic in Illinois earn a median of $48,520 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $39,400 and $58,310. The lowest-paid tenth earn under $33,800 and the highest-paid tenth earn over $70,470. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 2% above the national median of $47,720 for the same job.
  • Among the 37 states and territories where the Bureau of Labor Statistics publishes a reliable median for this job, Illinois ranks 18th by median pay. Rhode Island is highest at $61,350 and Puerto Rico lowest at $26,030.
  • 2,750 people hold this job here, 4.5% of the 60,840 who hold it across the country.
  • Of every 1,000 jobs here, 0.45 are this job, which makes it 15% more common here than in the U.S. as a whole.
  • The middle half of workers earn between $39,400 and $58,310, a band $18,910 wide.
  • Pay at the 90th percentile ($70,470) is 2.1 times pay at the 10th ($33,800).
  • The average (mean) is $50,450, 4% above the median. An average above the median means a smaller group of high earners pulls it up.
  • By the hour, the published median is $23.33.

Illinois requires pay or a pay range in job ads from covered employers. What Illinois’s rule says

Where This State Ranks

Its place among 37 states and territories, by median pay for this job.

All States
RankStateMedian PayPeople in the JobAgainst U.S.
16Utah$49,000410+3%
17New York$48,9301,400+3%
18Illinois$48,5202,750+2%
19Georgia$48,4102,560+1%
20Louisiana$47,9305800%

What Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic Do

Set up, operate, or tend machines to extrude or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes.

Common job titles: Equipment Technician (Equipment Tech), Extruder Operator, Extrusion Line Operator, Extrusion Operator, Extrusion Press Operator, Machine Operator, Metal Inspector, Setup Operator, Wire Mill Operator, Wire Mill Rover.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Reel extruded products into rolls of specified lengths and weights.
  • Measure and examine extruded products to locate defects and to check for conformance to specifications, adjusting controls as necessary to alter products.
  • Start machines and set controls to regulate vacuum, air pressure, sizing rings, and temperature, and to synchronize speed of extrusion.
  • Weigh and mix pelletized, granular, or powdered thermoplastic materials and coloring pigments.
  • Determine setup procedures and select machine dies and parts, according to specifications.

Education. 61% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

The Same Job in Other Places

All Places for This Job

Embed This Card

Paste this where you want the card to appear. It stays up to date.