Search job, employer or placeSearch cards/Check an Offer
SalaryNo.S-159131

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic

Providence-Warwick, RI-MAGovernment job code 51-4021

Market pay · all workers · BLS, May 2025

$56,020median pay per year · $26.93 an hour
10th
$45,150
25th
$47,990
Median
$56,020
75th
$66,960
90th
$66,960

Small sample: BLS marks this estimate as less reliable, so treat the figures with care.

Government wage levels · wage year 2026-27

Level I
$45,906
Level II
$51,397
Level III
$56,867
Level IV
$62,358

The four pay levels the Department of Labor sets for this job in Providence-Warwick, RI-MA. Yearly figures are the hourly level times 2,080 hours.

Filed pay

Fewer than 10 certified full-time filings for this job here, so there is no filed-pay figure.

People in this job here
650
Against the U.S. median
+17%
Mean pay per year
$56,940
Source: U.S. Bureau of Labor Statistics, May 2025 data · checked Nov 16, 2026
SourcesNo.S-159131

Where This Card Comes From

We show the government's numbers as published. Yearly pay is the hourly figure times 2,080 hours. Nothing is modelled or guessed. The U.S. comparison uses the national median for the same job code.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Content hash f52ac062 · first dealt Nov 16, 2026 · last changed Nov 16, 2026

Save as Image Compare

jobs.cards/c/S-159131

What Does This Job Pay in Providence-Warwick, RI-MA?

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic in Providence-Warwick, RI-MA earn a median of $56,020 a year, according to the U.S. Bureau of Labor Statistics survey for May 2025. Half earn between $47,990 and $66,960. The lowest-paid tenth earn under $45,150 and the highest-paid tenth earn over $66,960. These are government survey figures, not estimates from ads.

Checked Nov 16, 2026Source: U.S. Bureau of Labor Statistics

Reading the Numbers

Worked out from the published figures on this card. Nothing here is an estimate.

  • The median here is 17% above the national median of $47,720 for the same job.
  • It is 9% below the Rhode Island median of $61,350.
  • 650 people hold this job here, 1.1% of the 60,840 who hold it across the country.
  • Of every 1,000 jobs here, 0.91 are this job, which makes it 2.3 times as common here as in the U.S. as a whole.
  • The middle half of workers earn between $47,990 and $66,960, a band $18,970 wide.
  • Pay at the 90th percentile ($66,960) is 1.5 times pay at the 10th ($45,150).
  • The average (mean) is $56,940, within 3% of the median, so pay is spread fairly evenly around the middle.
  • By the hour, the published median is $26.93.
  • The market median of $56,020 meets government wage Level II for this job and area (wage year 2026-27).

What Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic Do

Set up, operate, or tend machines to extrude or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes.

Common job titles: Equipment Technician (Equipment Tech), Extruder Operator, Extrusion Line Operator, Extrusion Operator, Extrusion Press Operator, Machine Operator, Metal Inspector, Setup Operator, Wire Mill Operator, Wire Mill Rover.

What the Work Involves

The five tasks that workers and experts surveyed by O*NET rate most important for this job, most important first.

  • Reel extruded products into rolls of specified lengths and weights.
  • Measure and examine extruded products to locate defects and to check for conformance to specifications, adjusting controls as necessary to alter products.
  • Start machines and set controls to regulate vacuum, air pressure, sizing rings, and temperature, and to synchronize speed of extrusion.
  • Weigh and mix pelletized, granular, or powdered thermoplastic materials and coloring pigments.
  • Determine setup procedures and select machine dies and parts, according to specifications.

Education. 61% of workers surveyed by O*NET said the level required for this job is: High School Diploma or the equivalent.

Preparation This Job Usually Needs

Job Zone 1-2: Very Little to Some Preparation Needed. Usually requires a high school diploma or GED, though some occupations may not. Ranges from a few days to one year of on-the-job training. Some occupations may need little or no previous experience; others require several months to a year of experience. For example, landscaping and groundskeeping workers might require very little training or previous experience, while agricultural equipment operators can benefit from on-the job training.

This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.

Embed This Card

Paste this where you want the card to appear. It stays up to date.